stm32/boards/LEGO_HUB_NO6: Set filesystem label as HUB_NO6.
stm32/boards/NUCLEO_WB55: Fix LED ordering.
tools/mpremote: Implement seek and flush in ioctl method.
unix/Makefile: Use -Og instead of -O0 for debug builds.
extmod/modure: Redirect regex debug printing to mp_printf.
unix/coverage: Change remaining printf to mp_printf....
Initial port for Raspberry Pi Broadcom-based boards.
Preliminary support for asyncio cooperative multitasking.
bitmaptools : dithering and alphablend are new.
keypad.Event s now include timestamps.
framebufferio : support for IS31FL3741.
Espressif now provides I2CPeripheral , WiFi monitor mode, setting MAC address, ESP32-C3...
Initial port for Raspberry Pi Broadcom-based boards.
Preliminary support for asyncio cooperative multitasking.
bitmaptools: dithering and alphablend are new.
keypad.Events now include timestamps.
framebufferio: support for IS31FL3741.
Espressif now provides I2CPeripheral, WiFi monitor mode, setting MAC address,...
为 ESP32-C3添加USB/JTAG支持。使用USB作为编程和终端接口,不使用UART。
Add a new board type for ESP32-C3 revision 3 and up that implement the USB serial/JTAG port on pin 18 and 19. This variant uses the USB serial for programming and console, leaving the UART free.
Pins 18 and 19 are correctly reserved for this variant. Also pins 14-17 are reserved for flash for any ESP32-C3...
tools/dfu.py: Make tool work with python3 when parsing DFU files.
docs/rp2/general.rst: Fix typo with missing spaces.
py/gc: Add hook to run code during time consuming GC operations.
rp2: Enable optimisations (comp goto, map cache, fast attr).
py/mpconfig.h: Revert MICROPY_REPL_INFO to disabled at all levels.
rp2/mpconfigport.h: Use...
Initial port for Raspberry Pi Broadcom-based boards.
Preliminary support for asyncio cooperative multitasking.
bitmaptools : dithering and alphablend are new.
keypad.Event s now include timestamps.
framebufferio : support for IS31FL3741.
Espressif now provides I2CPeripheral , WiFi monitor mode, setting MAC address, ESP32-C3...
docs/reference/manifest.rst: Add docs for manifest.py files.
docs/reference/mpremote.rst: Add docs for mpremote.
docs/library/random.rst: Document the random module.
docs/rp2: Add reference for PIO assembly instructions, and PIO tutorial.
树莓派基金会在 2021 年 10 月 28 日发布了 Raspberry Pi Zero 2 W。官方售价 15 美元。
树莓派 Zero 2 W 使用了树莓派 3 的 BCM2710A1 作为 SoC。ARM 内核的时钟频率略微降到 1GHz,与 512MB LPDDR2 SDRAM 以一种非常节省空间的方式捆绑封装在一起。树莓派 Zero 2 W 的性能提升由工作负载而异,但对于多线程 sysbench,它几乎比上一代树莓派 Zero 快 5 倍。
Support for the CircuitPython development workflow over BLE.
Camera support on ESP32S2.
qrio: QR code decoding.
The keypad key-scanning module.
Run-time customization of USB devices.
Merging in of MicroPython fixes and enhancements as of MicroPython 1.16.
_pixelbuf is now adafruit_pixelbuf.
colorwheel()...
Changes since 7.0.0-beta.0The full commit log is here .
FIXES AND ENHANCEMENTS
Fix USB HID custom devices. #5214 Thanks to @dhalbert and @fasteddy516
Add displayio. for changing the refresh settings. Thanks to @amit-bsides
displayio.ParallelBus is now available as parallelbus.ParallelBus and will be removed from displayio in 8.0.0. Thanks to @jepler...
stm32/boards/LEGO_HUB_NO6: Add make commands to backup/restore firmware.
stm32/boards/LEGO_HUB_NO6: Skip first 1MiB of SPI flash for storage.
stm32/boards/LEGO_HUB_NO6: Change SPI flash storage to use hardware SPI.